Welcome Guest. Sign in or Signup

5 Answers

RPM ADJUSTMENT

Asked by: 3485 views Aerodynamics, Aircraft Systems, Student Pilot

Hello everyone

Plz guide me regarding rpm adjustmnt in case of engine flameout in normally aspirated engine.

Suppose  I was flying at 3000 feet AGL. I have adjusted 25 inch boost and 2500 RPM. engine FLAMES OUT. What should I do with RPM LEVER, IF IT is constant pitch propeller. Should I adjust it to fine or coarse position to get best glide ratio.

Ace Any FAA Written Test!
Actual FAA Questions / Free Lifetime Updates
The best explanations in the business
Fast, efficient study.
Pass Your Checkride With Confidence!
FAA Practical Test prep that reflects actual checkrides.
Any checkride: Airplane, Helicopter, Glider, etc.
Written and maintained by actual pilot examiners and master CFIs.
The World's Most Trusted eLogbook
Be Organized, Current, Professional, and Safe.
Highly customizable - for student pilots through pros.
Free Transition Service for users of other eLogs.
Our sincere thanks to pilots such as yourself who support AskACFI while helping themselves by using the awesome PC, Mac, iPhone/iPad, and Android aviation apps of our sponsors.

5 Answers



  1. Jim F. on Mar 13, 2013

    First off, a minor technicality: The term flame-out is only used with regard to jet engines. It’s literally when the flame in the combustion chamber goes out.

    But when you have an engine failure in a single recip with a CS prop, you loose oil pressure. That oil pressure is what changes the blade angle. Singles in this configuration are made to automatically go to fine-pitch condition upon loss of oil pressure. This is because if you still have engine power, you can still produce the most HP and be able to climb if needed.

    So relating directly to your scenario: noting. When the engine quits, you loose oil pressure, and the prop will go directly to fine-pitch. No need to adjust it manually, as moving the lever will do nothing.

    0 Votes Thumb up 1 Votes Thumb down 1 Votes



  2. khoda bakhsh on Mar 13, 2013

    @ Jim.F
    Thanks sir for helpful tip.

    0 Votes Thumb up 0 Votes Thumb down 0 Votes



  3. John D. Collins on Mar 13, 2013

    If the engine stops running, but is still turning, there will normally be oil pressure, unless you have had a catastrophic engine failure and lost the oil pressure thru a massive leak. In the latter case, the engine will seize within a minute if it hasn’t already done so, and the prop is very likely to stop.

    But if you just lost engine power because of running out of fuel, mismanaged your fuel, magneto’s failed, engine driven fuel pump failed, or the induction system iced over, the oil pressure will remain and the prop will be fully governable. In my Bonanza, without power, the engine RPM will remain at around 1800 RPM in the glide. The descent rate will be close to 1400 FPM. If I retard the prop control to the full rear stop, the RPM will reduce to 1100 to 1200 RPM and the descent rate will drop dramatically to about 800 FPM.

    My point is that a CS prop will still be governed by the prop control and not go to fine pitch and that you can use the prop control to reduce drag substantially.

    In a working engine, you need three things, fuel, fire, and air. If you able to supply all three, it will run. Normal troubleshooting to determine the reason the engine is not running involves all three being checked in your emergency procedures. Fuel tank selection, boost pump, mixture setting , throttle position, alternate air selection or carburetor heat activation, magneto setting are usually part of the emergency procedure found in your POH. To stretch your glide if you are unable to get your engine running, but it is still rotating, it is normally best in a single engine aircraft to retard the prop control to the full rear stop to provide the lowest drag.

    +5 Votes Thumb up 5 Votes Thumb down 0 Votes



  4. David Brown on Mar 15, 2013

    John is correct. you need to feather. In a twin it should feather for you.

    Just as a side note, and unrelated you are not providing 25″ of boost. If you were you would have someing in the rode of 51-52″ MP, as all you have done is remove pressure from ambient.

    On that topic I would say why on earth would you do that? Would you fly around with a clogged air cleaner restricting around 3″ of MP? No way!.

    These engine are meant to run Wide Open Throttle. Unless you want only a small amount of power for some other reason, why would you make a negative effect on volumetric efficiency?

    0 Votes Thumb up 0 Votes Thumb down 0 Votes



  5. khoda bakhsh on Mar 15, 2013

    Sir John D. Collins thankz so much for such value able comments..

    0 Votes Thumb up 0 Votes Thumb down 0 Votes


Answer Question

Our sincere thanks to all who contribute constructively to this forum in answering flight training questions. If you are a flight instructor or represent a flight school / FBO offering flight instruction, you are welcome to include links to your site and related contact information as it pertains to offering local flight instruction in a specific geographic area. Additionally, direct links to FAA and related official government sources of information are welcome. However we thank you for your understanding that links to other sites or text that may be construed as explicit or implicit advertising of other business, sites, or goods/services are not permitted even if such links nominally are relevant to the question asked.